solo assembly

Zenbooth Solo Build Instructions

ZENBOOTH

INTRODUCTION

Your Zenbooth has arrived!

We’re thrilled to welcome you into the peace and comfort of your new Zenbooth! Thank you for choosing a sustainable, people-friendly privacy solution for your space. Your decision supports not only your team’s productivity but also a healthier, happier community.

Your Zenbooth, carefully crafted in Berkeley, California, brings a touch of nature into your office. Made from eco-friendly materials like FSC-certified wood, formaldehyde-free finishes, and recycled insulation, your booth is designed to enhance focus and privacy while minimizing environmental impact. We’re proud to partner with local suppliers and reduce carbon emissions through sustainable sourcing and lean manufacturing.

We can’t wait for you to experience the difference it makes in your workspace!

We’re Here to Help Every Step of the Way!

If you have any questions or run into any issues while building your Zenbooth, don’t hesitate to reach out — we’re a small team of real people here to help you.

Email us: support@zenbooth.net
Call us: (510) 646-8368

And remember, your Zenbooth comes with a 3-year warranty. Please feel free to contact us at any stage of your booth’s lifecycle — we’re here to ensure your experience is smooth and enjoyable from start to finish!

PRODUCT SPECS

Measurements

Weight

Skylight

Door

Desk

Walls & Color

Floor

Power & Data Unit

American made engineered wood panels with laminated maple interior and 2 exterior color options:

TOOLS INCLUDED

All tools listed above can be found in the small parts box

PARTS OVERVIEW HARDWARE

All fastener counts include one spare. All hardware can be found in the Small Parts Box.
All parts shown are to scale.

PARTS OVERVIEW SMALL PARTS BOX

ASSEMBLY NOTES

Before assembly!

Before beginning assembly, we recommend consulting a professional insured Zenbooth installer or general contractor. Warranty may be void if components are improperly installed.

Contact us at support@zenbooth.net for any additional information or customer support.

After unpacking, inspect all parts for damage. If any parts are damaged as a result of shipping, report them to Zenbooth Support with a photo before assembling so we can send you a replacement part.

After assembly, use a wet rag to wipe down any dust created in the installation process. Do not use ammonia based cleaners on the skylight. Use a commercial plastic cleaner, or mild soap and water for best results.

Place the booth a minimum of 4 inches away from wall to ensure adequate airflow. If the fan stops working, stop using the booth and contact Zenbooth for a replacement.

Additionally allow a minimum of 36 inches of clearance at the front of the booth for door access.

Safely execute the install with two people!

WARNING: Risk of Electric Shock, Fire, and Injury. Please read and follow all assembly instructions to safely assemble your booth.

ASSEMBLY STEPS

  1. Place Base on level ground. The booth can be moved after installation.

  2. Insert the Interior Left Wall into the Left side of the Floor.
    Note: One person needs to support this panel during this step to keep it from falling over.

  3. Slide the Interior Rear Wall into the joining grooves of the Base and Left Wall.
    Note: One person is needed to support this panel during this step until the panels are secured with screws.

  4. Insert the Interior Right Wall into the Base and Interior Rear Wall.

    Using 2” square drive screws, fasten the Right Interior Walls to the Rear Wall.

  5. Slide the Top & Bottom Vent Ducts into the slots on the inside of the Side Walls, bottoming it out against the Rear Wall.

  6. Insert the Exterior Rear Wall to the Base and join it to the Left and Right Interior Walls.
    Fasten Rear Wall using 2” square drive screws.

  7. Connect Fan Cord.

    • Make sure the 2-Pin Fan connectors are connected.
    • Once all cords have been connected and cleared, insert the Hatch Plate and move the Grommet in place.
  8. Insert the Universal Exterior Walls to the Base and Exterior Rear Wall.
    Exterior Walls are symmetrical and can be installed on either side of the booth.

  9. Evenly insert the Door Header into the corresponding notches in the left and right interior walls with the weather stripping facing out.

  10. Inserting the Facade into the Base at an angle will help ensure the correct fit.
    The outer edge of the Facade should bottom out on top of the Floor.

  11. Connect Ceiling Lights.

  12. Fasten the Skylight.

  1. Fasten The Walls -
  1. Attach Hinges to Door using 1/2” Philips screws to attach Top and Bottom Hinges to Door.

  2. Install Door Handle.

  1. Fasten Hinges -
  1. Hang the Door on the mounted Hinges. Connect the positioned Spring Hinge (Middle) to the door.

  2. Set Spring Hinge. Place Door in closed position. Insert Hex Wrench in Hex Hole. Rotate Hex Wrench clockwise to increase tension and insert locking pin loosely in adjusting hole. Check the door closing force.

TROUBLESHOOTING

Q: The Door “scrapes” across the bottom of the booth.
A: Insert shims into rear right corner of the booth.

Q: “The Door does not close by itself, is that normal”?
A: Repeat the hinge tension adjustment.

Q: My fan/light stays on continually.
A: If the timer does not seem to be turning the product off after 10 minutes, please contact Zenbooth support.

Q: My booth is stuffy or warm.
A: Ensure the fan is unobstructed and at least 4” from a wall or structure.

Q: The desk lift stopped operating. What can I do?
A: Steps to initialize a Zenbooth Adjustable Desk:

  1. Unplug the desk’s power cord wait 10 seconds and plug it back into the power source.

  2. Press the DOWN button on the desk until the desk reaches its lowest position. Release DOWN button.

  3. Press and hold the DOWN button for 10 seconds and then release.

  4. Hold the DOWN button again until the desk lowers slightly and raises back up.

  5. Your desk is ready!